Construction Chemicals

Product Details:

Mortars - a superior water resistant cement based specially formulated for joining the blocks. Mortar is specially designed and manufactured under stringent quality controls to give superior adhesive strength, higher durability and a strong bond between the blocks. This unique combination enables this mortar to be thinner, compact and versatile. It also ensures higher bond strength and durability at only 3 mm thickness compare to the conventional mortar at 12-15 mm replacing the conventional cement and sand mix mortar completely. Ready to use grey cement based non-shrink, self- curing, water resistance mortar for fixing AAC blocks, Concrete blocks, fly ash bricks etc.


Uses:Fixing and Jointing masonry units like AAC blocks, Concrete blocks, fly ash bricks etc.

Features:

Excellent bonding to the blocks/bricks, Better levelling, prevent seepage and water percolation, Pre-mixed, only water to be added.

 

Advantages:

Ready to use, only water to be added. Thinner jointing material with very high tensile adhesion strength improving the overall masonry strength. Better bond than conventional cement based mortar. Faster to apply due to good spreadable properties. Excellent high strength & water retention properties. Economical as quantity of mortar is less than conventional mortar. Self-curing.

• No curing is required after application. Thus saving water
• Thinner layer guarantees to be more cost-effective
• Easy to mix and faster to apply
• Plastering can be done after 24 hrs. of application

Applications:
If the substrate is very porous, if the temperature is high and/or the relative humidity low, it is advisable to dampen the surface. Do not leave any standing water. Apply a thin uniform Layer Block Joining Mortar 2 to 3 mm thick on the clean & levelled surface of masonry units using proper trowel Place the next course of masonry units on evenly jointing mortar bed in proper line & level. Each masonry unit shall be properly bedded and set in position by gently pressing with handle of trowel. Inside unit of the masonry unit shall be applied with mortar before the next unit is laid & pressed against it especially in case of bricks. Clean the excess material, if any immediately. Continue the procedure for the entire masonry work. Do not disturb the blocks /bricks setting for first 24 hours.

Benefites:

• Time and manpower is saved
• Lesser shrinkage and seamless structure
• High strength adhesion
• Consistency of material and quality
• Can be applied by ordinary mason – no special skill required

Product Details:

Chemical admixtures are the ingredients in concrete other than portland cement, water, and aggregate that are added to the mix immediately before or during mixing. Plasticizers or water reducers, and superplasticizer or high range water reducers, are chemical admixtures that can be added to concrete mixtures to improve workability. Unless the mix is "starved" of water, the strength of concrete is inversely proportional to the amount of water added or water-cement (w/c) ratio.

Admixtures are added in concrete to improve the quality of concrete. Mineral admixtures include fly ash (FA), silica fume (SF), ground granulated blast furnace slag (GGBS), metakaolin (MK), and rice husk ash (RHA) which possess certain characteristics through which they influence the properties of concrete differently.

Product Details:

Bonding Agents are a line of epoxy adhesives in low and high modulus variations with multiple viscosities to guarantee a proper bond. Bonding agents are natural, compounded or synthetic materials used to enhance the joining of individual members of a structure without employing mechanical fasteners. These products are often used in repair applications such as the bonding of fresh concrete, sprayed concrete or sand/cement repair mortar to hardened concrete.
Two of the critical factors affecting the bonding between new and old concrete, provided sound concrete practices are followed, are

• the strength and integrity of the old surface and
• the cleanliness of the old surface.

The main types of bonding agents used in construction are latex emulsions and epoxies. This Update reviews the properties of each and guides the user and the specifier on their advantages and limitations.
We are offering wide range of Bonding Agents and Grouts based on the requirements.

Product Details:

These are available in different grades and categorized brand to brand and company to company but shared in general sense as, Silver Star – Type I Silver Star: General purpose tile adhesive for ceramic tile, tile on tile for wall and flooring application. Gold Star: Higher grade of water resistant tile adhesive suitable for Vitrified, Marbonite wall and floor application. Platinum Star – Type II Platinum Star: White Cement based tile adhesive for fixing Marble, Granite, Glass tiles etc. for wall and flooring application.

Features

• Excellent bonding to the base plaster/concrete even at a thickness of 2 mm
• No need for hacking and Good workability
• Water resistant and Can be used on new as well as old walls and floors
• Ease of use at site and Suitable for interior
• Suitable for exterior along with additional metal anchoring
• Consistent work quality and Durability
• Saves time and Increase productivity
• Cost effective and No curing required

Advantages

• Good workability and Ease of use at site
• Suitable for interior and Consistent work quality
• Suitable for exterior along with additional metal anchoring

Benefits

• Durability Saves time and Increase productivity and Cost effective
• No curing required and Saves time and Increase productivity

Product Details:

Product Details: